7cm Wood Grain Skirting Boards

Key Advantages

• Wood grain fidelity: Printing resolution ≥300 dpi with ≥16 grayscale levels. Texture depth 0.15–0.3mm. Grain details (annual rings, vessels) achieve ≥90% similarity to target wood samples based on texture feature matching algorithms.
• Moisture and insect resistance:
• Water absorption: PVC/WPC ≤1.2%, SPC ≤0.2% (24H, 23°C)
• Termite resistance rating: Grade 9 per GB/T 18260 (mortality ≥90%, wood damage rating ≤1)
• No swelling or cracking after 30 days at 70% RH
• Dimensional stability: Linear expansion coefficient ≤7×10⁻⁵/℃ (PVC), ≤4.5×10⁻⁵/℃ (WPC), ≤3.5×10⁻⁵/℃ (SPC). Under temperature 15-35°C and humidity 40%-80% variation, lengthwise dimensional change ≤0.5mm/m.
• Pre-finished and low maintenance: Decorative layer is factory-applied. Stain resistance rating ≥4 (GB/T 9780). Routine stains removed with damp cloth. Xenon arc aging (500h): ΔE ≤3.
• Cost efficiency: Unit length price approximately 30%-50% of solid wood skirting with comparable appearance, with no additional painting or finishing costs.

Product Specifications

Application Scenarios

• Wall base finishing in natural wood style residential living rooms, bedrooms, and studies
• Floor-to-wall transition in minimalist interior spaces
• Skirting board complementing dark wood doors and wooden grilles in Neo-Chinese style interiors
• Wall base protection and decoration in boutique hotels, tea houses, and resorts
• Base finishing in offices, clubhouses, and exhibition spaces requiring wood veneer aesthetics
• Covering existing damaged skirting or lower wall sections in renovation projects

Frequently Asked Questions and Precautions

Q: Do water stains or white fog appear on the wood grain surface?
A: Heat transfer and lamination processes create a sealed surface without wood pores, so water stains do not form. Prolonged immersion (>24 hours) may cause edge seal failure and edge discoloration, but not white fog. Wipe dry after routine cleaning.

Q: Color variation between different batches?
A: Within-batch color difference ΔE ≤1.0. Between-batch ΔE ≤1.5–2.0 (Pattern-dependent). Purchase sufficient quantity for a room or continuous wall in a single order. If mixing batches is unavoidable, use corners or door openings as transition points.

Q: Can this skirting be used in rooms with radiant floor heating?
A: Yes. Recommendation order: SPC substrate (thermal conductivity 0.35–0.45 W/(m·K)) > WPC (0.25–0.35 W/(m·K)) > PVC (0.17 W/(m·K)). Leave a 3–5mm expansion gap between skirting bottom and floor during installation. Avoid PVC substrate with prolonged exposure to >40°C.

Q: How to achieve nail-hole-free installation?
A: Three options: ① Adhesive-only installation (for flat substrates); ② Brad nails into pre-formed back slots — no visible marks on face; ③ Clip-mounting system — removable skirting with no face nail holes. Avoid nailing directly through the wood grain surface.

Q: How to handle gaps between skirting and wood flooring?
A: Gap ≤2mm: apply color-matched mold-resistant sealant. Gap 2–5mm: use matching bottom-edge sealing strip or PVC transition strip. Gap >5mm: check floor or skirting installation levelness and re-adjust.

Precautions

• Store skirting flat in the installation environment for at least 24 hours before installation to acclimate temperature and humidity.
• Wall substrate must be flat (≤2mm over 2m), dry (moisture content ≤10%), and free of dust and oil.
• Use fine-tooth saw blades (≥80 teeth) for cutting. Lightly deburr cut ends with 200–400 grit sandpaper. Avoid dull blades that may chip the wood grain layer.
• Apply adhesive in a wavy or dotted pattern (15–20cm spacing) with adhesive within 5cm of ends. Use neutral or MS polymer adhesives. Avoid acid-cure silicone (may corrode surface).
• For bathroom dry areas or kitchens, apply mold-resistant sealant at both top-wall and bottom-floor joints.
• Clean with a soft cloth or sponge dampened with neutral cleaner (pH 6–8) and wrung until almost dry. Avoid steel wool, abrasive pads, or cleaners containing abrasives, strong acids, or alkalis.
• Store horizontally on dry ground with soft separators between pieces. Avoid direct sunlight and high temperatures (>45°C). Stack height ≤1.2M.
• Avoid wet mopping floors within 48 hours and extensive water exposure to walls within 72 hours after installation to allow complete adhesive curing.