Carved PU Mouldings & Cornices

Key Advantages

• Face width 12.6cm, pattern repeat 27.2cm; Modular design facilitates installation layout
• Symmetrical carved pattern design with continuous pattern alignment at joints; No on-site pattern matching required
• PU material density lower than gypsum or wood mouldings, reducing weight for easier handling and installation
• Moisture and insect resistance: Non-absorbent and not susceptible to insect infestation; Suitable for humid environments
• Dimensional stability: No cracking or deformation under standard temperature and humidity ranges
• Smooth surface: Ready to install without on-site sanding or painting

Product Features

Application Scenarios

• Ceiling trim (cove moulding at ceiling-wall junctions)
• Wall waistline (mid-height wall division and decoration)
• Accent wall borders (panel frames, picture frame-style accent walls)
• Door surround decoration (moulding around door frames)
• Wainscoting top and bottom trim (edge finishing for wall panels)
• Commercial project trim (hotels, clubs, showrooms, sales centers)
• Mirror and picture frame decoration (wall-mounted frame mouldings)

Frequently Asked Questions

Q1: What does the pattern repeat length of 27.2cm mean?
The pattern repeat length refers to the length required to complete one full pattern cycle between adjacent moulding sections. When installing, cutting or joining at multiples of 27.2cm ensures continuous pattern alignment at joints without manual pattern matching.

Q2: How are the mouldings installed? What auxiliary materials are required?
Apply with specialized PU moulding adhesive or neutral mold-resistant construction adhesive. The substrate must be flat, dry, and free of grease. Apply adhesive to the back of the moulding, press into place, and fill joints with color-matched filler. For corners, use 45° miter cuts or dedicated corner accessories.

Q3: How does this product compare to gypsum mouldings?
PU mouldings weigh approximately 1/3 to 1/2 of gypsum mouldings, allowing single-person installation. No on-site gypsum mixing, sanding, or painting is required—install directly after adhesive application. PU does not absorb water, does not develop mold, and does not crack, making it suitable for humid areas such as kitchens and bathrooms.

Q4: How does this product compare to wood mouldings?
PU mouldings do not absorb moisture and have no swelling, shrinkage, deformation, or cracking issues common to wood mouldings. The surface requires no filling, sanding, or painting before installation. PU is not susceptible to insect infestation, making it suitable for termite-prone regions.

Q5: Does the product require painting after installation?
The product comes pre-primed or with a white finish (depending on product series) and is ready to use after installation. For color changes (e.G., Gold, black, wood grain), the surface accepts water-based or polyurethane paints with good adhesion.

Q6: How are corners handled?
For both external and internal corners, use 45° miter cuts. Cut the moulding ends at 45° using a utility knife or miter saw, apply adhesive, and join. Alternatively, use dedicated corner accessories if available from the product line.

Precautions

• Verify substrate flatness before installation: height difference ≤ 3mm when measured with a 2-meter straightedge. Substrate moisture content within applicable standards
• Storage requirements: Store flat on dry ground with stack height not exceeding 1 meter; Avoid heavy pressure that may cause deformation. Keep storage area away from direct sunlight
• Use fine-tooth saw blades (tooth spacing ≤ 3mm) or score multiple times with a utility knife when cutting; Wear safety goggles. Apply color-matched paint or filler to cut edges
• Recommended installation ambient temperature: 5°C to 35°C. Avoid low temperatures that may slow adhesive curing
• Apply adhesive evenly and ensure full contact between moulding and substrate. Use painter's tape for temporary fixing until adhesive cures
• Joint treatment: Apply filler to butt joints between moulding sections, smooth with finger or damp cloth, and lightly sand with fine sandpaper after drying
• Inspect pattern alignment and color consistency across multiple batches before large-scale installation
• Avoid cleaning with strong acids, strong alkalis, or organic solvents
• Handle carefully during transport to prevent damage to carved areas
• For installation in humid areas (bathrooms, kitchens), seal the back and joints to prevent moisture penetration